Complete needs restoration. North of Syracuse. Thanks, Ron

Does anyone have a scan of the Mech Control Schematics for a Rowe Ami R-88 Mech control board? I have a parts and service manual, it's the "MECHANISM CONTROL” 4-07221-02 The board is labled 6-08708-03. The Juke is new to me, but it just rotates the basket continuously. The trouble shooting...

Has anyone replaced the field coil or had one replaced on a Seeburg? It doesn't look as if the coil is bolted on, which makes it more difficult to remove. Anyone know how to test one of these? There are three leads attached to the speaker. I read with a VOM the two leads that go down through the...

Serious collector will pay cash and pick up all rockola shuffleboard tables and related equip. such as electric scoreboards, lights, pucks, signs, etc. Might be interested in other older tables. 417 860 3030

It need not have all the tubes but would like working transformers

Got one? I need one and dont want to buy repro. Post up info if you have one available Mike

Anyone have the images for the NSM control center? The 2708 and 2716? I need to get a set burned, but don't have the images available. I tried the 2732 hack here - http://tuukan.fliput.net/festival_en.html with no luck. I've pretty well shotgunned the ic's and it will semi work with...

Picked up a couple of Prestige E 160 s look to be in good shape but they're all locked up and no keys ........hate to get the drill out........anybody have NSM keys available ......... TIA

Title says it all. Another scam artist. Got me while trying to buy a Hollycrane manual from him. Rick.

I'm looking for 3 or 4 AMI mechanism motors. Used in Stream-Liner, Top-Flight, Singing Towers etc. Must be in perfect working order. Who can help ?? Best regards, Jo van Dongen.

Hello all, I had a working wallbox system in my Rowe MM4 that I pulled out this weekend because I'm going to sell the juke. I believe this equipment will work in MM1, MM2, MM3, MM4, MM5, TI-1, TI-2 jukes. Maybe some others that I don't know about... I have a working wallbox, stepper unit, and...

Output Transformer for an AMP model R-111/R-113 used in Jukebox AMI model D-40 Power Transformer for a Seeburg TSR3-L6 Cartridge for a Seeburg Crown 20 selection that plays 78rpm using an amplifier model "830 -1Z Cheers Roger

This was in todays paper. There moving from Grand Rapids Michigan to Mexico. http://www.battlecreekenquirer.com/apps/pbcs.dll/article?AID=200990227010 -- John P. Dayhuff Battle Creek, MI. Ph. 269-979-3836

I would appreciate hearing back from you if you are parting out a 1422 or 1426 20-play mech and would consider selling me a few small parts. I suspect that a 1428 might also have the parts I need. With thanks,John (Alberta Canada)

Hi I have a '57 KD200 with the redhead cartridge. I just came across a pickering 345-03D cartridge and swapped out the old redhead. I know I'm supposed to replace a 10K resistor with a 47K resistor but which one? Where is it? What do I need to remove in order to get to it? Any help would be...

Nice solid complete seeburg B Near Syracuse New York. Winter Project that never got started. Need to sell it quick, taking offers. Thanks 315-947-5846 Ron

Hey everyone... I have an SMC1 that is completely dead right now. I picked it up and it was somewhat flaky with the mech going into slow motion and I thought it could sound a little better too. I rebuild the amp with new caps and output transistors and replaced a motor cap. Went to give it a run...

Hello I have acquired a cancel switch and am wondering if anyone knows where to tap into the harness for Seeburg V200. I do not want to run wires to the mech if I can help it. Thank you, Mark.

We have another of our film rentals showing up - Watchmen - in the "Mafia Bar" look for our V200... http://www.flippers.com/props.html John :-#)# -- (Please post followups or tech inquiries to the newsgroup) John's Jukes Ltd. 2343 Main St., Vancouver, BC, Canada V5T 3C9 Call...

Hi, I need the lower chrome speaker grill for a Seeburg DS-100/160 in decent shape, can anyone help me out? Thanks, SLS