All - I know these are hard to find. Just thought I'd ping the group to see if anyone had seen on recently. Thanks! Steve in Worcester, MA

I am wanting to recap the 55015-1A amplifier in my Rockola 498. I have ordered a manual from Victory Glass which covers this juke, but when it comes to the amplifier it displays the amplifier and parts list for the Super Sound 490 models. Which is close, but not the same. Would anyone happen to...

On Monday, July 16, 2001 10:32:33 PM UTC-5, Don Westphal wrote: Late 60's Seeburg LS1 jukebox for sale. 160 selections stereo. Machine is in above average condition and it works! Located in Phoenix. Digital pics available. Only $250.00 hi would you mind sending me those pictures my aunt...

letter and number latch bar adjustment bolts what kind of tool is used (besides pliers) to turn the flat on the adjust bolt

I have a Wurlitzer model 1400 that when you make a selection the wobble plate will move a little but not enough to move the yoke and engage the over ride limit switch. I have tried to adjust the switch and the fulcrum but nothing happens. Any ideas? the only things i could think would be to...

Hello everyone. As the title says, I cannot get the 443 to play selections from the wallbox. I hard wired the power/signal/ground to the stepper but the pin bank just keeps circling and the letter and number keys on the 443 itself do not register.

I found a couple more parts while cleaning up. I know one is a juke part but not sure to what model / type. The other I have no clue on. Hoping somebody here can help us out. Pictures are again on our facebook page: https://www.facebook.com/HTEIndustries If there is a way to embed them here let...

I am near completion of my rockola juke. It had all 4 ohm speakers in it that were destroyed. I have 4 replacement 8 ohm speakers in it now. 2 10's and 2 6's. I have 1 of each connected in parallel on both the left and right channel. I know this gives me an impedance of roughly 4 ohms on my left...

will seeburg wallbox motor from V 3 WA fit seeburg W 3 1, thanks Tom

picked up 2 very nice wallboxes have original seeburg keys and locks,they look very good,they have very little pits in chrome,can i do anything to buff them out or just leave alone

working on nsm floor model was doing odd stuff so we wanted to clean the eye on motor that runs the tray. eye was dirty but now it picks all cd but won't return ones in middle of rack on left side and sometimes right side dose that motor have to be put in a certin way? is it a stepper...

Hi everyone. Just acquired a very nice Wurlitzer 61. She needs a few bits. Can anyone hook me up with the following? 30487- name plate escutcheon 30488 - name plate croglass 31703 - Selector front plate Many thanks. George in jersey

Thanks for the quick reply. Im looking for remote control units, not wall boxes or steppers. In the past Vern Tisdale sold me several remote control units for all my Seeburg jukeboxes. I want a remote control so i won't have to reach behind the jukebox every time I want to play a record, and I...

Have a Wurlitzer Colonial model 780 for sale. This 1941 with coin mech is ready for U. I've had it for 30+ years and would probably rather not hall it to the Chicagoland Show Nov 14-16 . But I will unless I get a decent offer before that. Pictures are available you can contact me at...

need a seeburg wallbox 3 W 1 to test stepper and later use,like 1 in missouri if possible so I can go get it

have a thorpe cartridge any tips on adjusting tone arm preasure

I have the remote volume controller with cancel (model 169B) - can anyone help with instructions for installing this on a model 3200 jukebox? Does it need anther part on the amp? Thank you, John

I have a nice older restored "B" I'm looking to sell. Decent veneer (re-do) and very nice chrome. Mech now gets 'sticky' due to low usage. Very nice looking machine, though. Have plenty of pix. 1750.00 you can either post here of email me at ha.2065 AT yah00 if interested!

Have 24 record holder for packard play more also tone arm

On Saturday, January 3, 2015 at 10:58:33 AM UTC-6, Tom Reid wrote: what gauge wire for mrvc1 remote volume control use found the wire thanks