I'm going to try my hand at building a stand for my machine and I'd like a few dimensions to work with. I'd also like to know the angles and attachments. All I'm looking for is a few pictures. Thx Pat

I'm going to start restoring the empress but need help with the cabinet. The wood that curves around the upper left red plastic that has the groves in it has broken away at the first groove. Does it matter what kind of wood I replace it with? Does anyone know what kind of wood the cabinet was made...

My SPS 160 with a DCC3 scans twice and shuts off when you power it up. After that it will select and play fine. Any ideas?

Looking for a wooden coin box that went with a rockola shuffleboard scoreboard. The box is about 18" tall and has a black metal front door with a 6X8" silk-screened glass insert. Really just need the glass but will buy the whole thing. Glass says "play rockola shuffleboard" and tells how many coins...

Restoring this from the bottom up. The 5u4 blows every time I plug the speaker connector in, even with speaker not connected. Voltages are good on tube,has been re-capped and can't find a short anywhere. Any help will be much appreciated!!

First off, let me say that I am a newbie and perhaps that will explain my problem. I am having a problem getting sound out of my Rowe CD-100-E. At first I could only get sound from one channel, so I took the amp out and saw the 8a fuse at F1 was blown on one of the driver boards (40710104),...

For sale are the most of the castings for the jukebox. The cabinet was beyond restoration. Includes the selection castings, towel bars, bullets, etc. Most will need to be plated. The package also includes other parts including the amp and receiver and other parts. $500 for pickup near Philly,...

Hello all Anyone out there a Music Mite expert? Problem is the amplifier, recapped, changed 2 bad resistors and checked the tubes. I now have sound but no volume, the 270ohm resistor is cooking. Pin 7 on the 6X4 I am getting 20vac and nothing on the other side of the 270ohm res. I think the...

Hi, I need the Automactic Volume module that plugs into the preamp, it looks like a plug-in relay, it is mounted on the preamp board close to the volume control. Let me know what you have, Thanks.

Won't park? Get it to date cuter guys...

I am thinking of purchasing a Rowe Saturn CD Jukebox. It is my first box and it appears to be in good condition, is this a good choice?

Will pick up and pay cash for rockola shuffleboard tables and all related equip. such as EM scoreboards, coinboxes, pucks, lights and all advertising. 417 860 3030

My 66 Wurlitzer selector buttons engages (when I push a letter and number)and the selector turns but my coils don't trigger and select the pin. I am able to select and play a record by pulling up a pin or by pushing the coil manually. I checked the fuse (8/10), which was shot and replaced it....

Hi Guys, Hate to admit it but I'm stuck (sic) and could use some advice. My 1650 selects a record normally, plays it but when the record is over the spindle only drops maybe 2/3 of the way down. When the record tray tries to retract it jams because the spindle is in the way. The spindle shaft...

My 1937 Wurlitzer 24 is having repeated selection issues; it selects the same record again & again. I have tweaked the mechanism in the past to get it working properly again, but the area where the star shaped gear is located is pretty gummed up with grease, so within a week the problem...

This might be a stupid question, but aside from physical damage or defects, when should this be done? The reason I'm asking is that on my RO1454, I've had the amp rebuilt, new tubes (two different matched pairs), new cartridge installed (P51 with a .7mil stylus), and I'm still not 100% happy with...

I have a 1468 R-O that runs to fast. I tested it with a tach. It's not much, but just enough to be able to tell. Dia. of mtr. shaft checks out. Has new idler wheel. Compared to another mtr. Spring on end of mtr. shaft is ok. Any ideas? Thanks

Hi, I took out my cd player to clean it. its not been used in 3 month. I forgot which wires to go so i got a board error on the mech. so i turn it off. got my manual out. i did hook up wrong.so i hook it up right and the cd player doesnt do anything. i can pick a song and the arm can put the cd on...

I'm new to this group. My neighbor has a Seeburg SS160 which works but plays a little slow. Does anybody have a schematic in pdf format? In the pinball world we have ipdb.org with manuals and schematics for everything.

Milwaukee to chicago area, are there any old timers still around that really know their way around 45 jukes ? new timers is fine too.....