If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Continental Parts (UPDATE!) Or have tips
Well I went and looked at the juke...I was going to buy it but I noticed
another issue. The metal bracket that holds the title board to the back of the jukebox is bent forward. Is that common? Is it fixable? Are they available? -- Ken In Texas http://www.pinballrebel.com Custom Pinball Cards, Jukeboxes, Drive In's "Never ask a man if he's from Texas. If he is, he'll tell you on his own. If he ain't, no need to embarrass him." |
Ads |
#2
|
|||
|
|||
Continental Parts (UPDATE!) Or have tips
On Mar 29, 9:38 am, Ken In Texas wrote:
Well I went and looked at the juke...I was going to buy it but I noticed another issue. The metal bracket that holds the title board to the back of the jukebox is bent forward. Is that common? Is it fixable? Are they available? most that I have ever seen are bent forward (due to 40+ years of supporting the weight of the titleboard and glass on such a small piece cast from ****-metal.) the usual fix is to use longer screws, and pack out with many washers to tilt the titleboard forward at the bottom. I would be absolutely amazed if this part were available anymore, of if undamaged used ones were available. Reproduction ones might be available. -- Ken In Texashttp://www.pinballrebel.com Custom Pinball Cards, Jukeboxes, Drive In's "Never ask a man if he's from Texas. If he is, he'll tell you on his own. If he ain't, no need to embarrass him." |
#3
|
|||
|
|||
Continental Parts (UPDATE!) Or have tips
Yes, No, Yes.
"Ken In Texas" wrote in message ... Well I went and looked at the juke...I was going to buy it but I noticed another issue. The metal bracket that holds the title board to the back of the jukebox is bent forward. Is that common? Is it fixable? Are they available? -- Ken In Texas http://www.pinballrebel.com Custom Pinball Cards, Jukeboxes, Drive In's "Never ask a man if he's from Texas. If he is, he'll tell you on his own. If he ain't, no need to embarrass him." |
#4
|
|||
|
|||
Continental Parts (UPDATE!) Or have tips
the neck as they call it usually cracks in the webbing and sometimes can be
seen on the outside as well. Usually these are caused from handling the juke by the title case. The neck was designed to support the title case but was not designed to provide a hand hold for dollying the juke MRT "Keith Stelter" wrote in message . .. Yes, No, Yes. "Ken In Texas" wrote in message ... Well I went and looked at the juke...I was going to buy it but I noticed another issue. The metal bracket that holds the title board to the back of the jukebox is bent forward. Is that common? Is it fixable? Are they available? -- Ken In Texas http://www.pinballrebel.com Custom Pinball Cards, Jukeboxes, Drive In's "Never ask a man if he's from Texas. If he is, he'll tell you on his own. If he ain't, no need to embarrass him." |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Continental Parts (Anyone have these?) Or have tips | Ken In Texas | Juke Boxes | 6 | March 23rd 07 10:09 AM |
AMI Continental parts needed | Serial # 19781010 | Juke Boxes | 1 | October 1st 04 03:13 PM |
Ami Continental parts sought | Serial # 19781010 | Juke Boxes | 1 | September 28th 03 01:29 PM |
Ami Continental Parts Needed Can you Help! | Serial # 19781010 | Juke Boxes | 0 | September 24th 03 11:04 AM |
NEED: AMI Continental II parts | mike | Juke Boxes | 0 | August 3rd 03 01:51 AM |