If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#21
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
On Apr 3, 8:37*pm, elkridge pinball wrote:
On Apr 3, 6:25*pm, Ken Layton wrote: On Apr 3, 12:54*pm, elkridge pinball wrote: Well, I finally found the manual part number: Operations Sequence and Schematics (part # 3-65355-12) Anyone have one they would like to sell???? That's the part number of the R90 Shop Manual that I have. It has 73 11 x 17 pages that are double sided! The lamp driver stuff is only two pages: a schematic on one page and a parts list on the other. They probably only made one shop manual for each "revision". *Maybe had updates sent out for changes in the models. PARTIAL SUCCESS!!!! I found another bad diode, replaced and now I have flashing lights!!!! They flash to a set pattern. Still cant get to flash to music, if I switch to flash to music, still flash to set pattern. Adjusting sensitvity has no effect. Well, 2 out of 3 so far, lights on, flashing, now need the last.... Thanks so far to everyonr who has helped. |
Ads |
#22
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
I've seen the slide switch go bad.
|
#23
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
On Apr 5, 2:36 am, Ken Layton wrote:
I've seen the slide switch go bad. and fall apart too ..... |
#24
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
After much digging and looking, it appears that this may be a common
problem with trying to get some schematics for Rowe equipment. Rowe says that they were put in storage due to space considerations years ago when they relocated buildings. They gave me the usual list of possible sources, but no luck. |
#25
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
On Apr 14, 7:38*am, elkridge pinball wrote:
After much digging and looking, it appears that this may be a common problem with trying to get some schematics for Rowe equipment. *Rowe says that they were put in storage due to space considerations years ago when they relocated buildings. *They gave me the usual list of possible sources, but no luck. You never emailed me with your snail mail info so I could have a place to send it after i copied it. |
#26
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
On Apr 14, 11:19*am, Ken Layton wrote:
On Apr 14, 7:38*am, elkridge pinball wrote: You never emailed me with your snail mail info so I could have a place to send it after i copied it. I got a copy of the schematic for the lamp control 6-09255-03. Is that the one you have. This is for the R-90 I believe. I was hoping it was similar to the R-92, but no luck. The drwg is Fig. 2-7, Lamp Control Assembly (4-07501-03-Q2). Thanks Ken for following up. |
#27
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
On Apr 15, 12:38 am, elkridge pinball wrote:
After much digging and looking, it appears that this may be a common problem with trying to get some schematics for Rowe equipment. Rowe says that they were put in storage due to space considerations years ago when they relocated buildings. They gave me the usual list of possible sources, but no luck. In my experience they don't seem to be interested in helping with finding faults or providing info. Usually Emails are ignored, Im surprised that you even got a reply. real "ashtray on a motorbike" stuff. ... |
#28
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
On Apr 14, 9:36*am, elkridge pinball wrote:
I got a copy of the schematic for the lamp control 6-09255-03. *Is that the one you have. *This is for the R-90 I believe. *I was hoping it was similar to the R-92, but no luck. The drwg is Fig. 2-7, Lamp Control Assembly (4-07501-03-Q2). Thanks Ken for following up. Yeh, that's the one I have from the R90 shop manual. |
#29
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
On Apr 14, 12:36*pm, elkridge pinball wrote:
On Apr 14, 11:19*am, Ken Layton wrote: On Apr 14, 7:38*am, elkridge pinball wrote: You never emailed me with your snail mail info so I could have a place to send it after i copied it. I got a copy of the schematic for the lamp control 6-09255-03. *Is that the one you have. *This is for the R-90 I believe. *I was hoping it was similar to the R-92, but no luck. The drwg is Fig. 2-7, Lamp Control Assembly (4-07501-03-Q2). Thanks Ken for following up. Finally got back to taking a look at this thing. Disassembled and cleaned the contacts in the selector switch, all looks OK, continuity checks good. Replaced the 1 megohm sensitivity potentiometer since I was getting "weird" readings. Everything still works as it did before, but still no flash to music. Anyone know the input to the board? I know 2 wires come from the amp, I wonder if one is a mute circuit as shown in the R90 schematic. |
#30
|
|||
|
|||
Rowe R-92 Lamp Control Board Schematic
Hopefully get to work on this project this weekend!!!
have a second board to play around with now. Fingers crossed! |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
AMI Rowe R87 schematic? | Jussi Saily | Juke Boxes | 9 | November 11th 07 07:35 PM |
Rowe R-83: Looking for an amp schematic | GottliebDomino | Juke Boxes | 0 | June 11th 06 01:39 AM |
TECH - Rowe R-84 Jukebox CR123 diode on central control board | John | Juke Boxes | 0 | March 25th 06 03:03 AM |
WTB: Lamp control box (flasher box) for R-92 | Doug_H | Juke Boxes | 1 | January 10th 06 04:16 AM |
AMI/ROWE r-83 mech. control board. | Dennis Lavin | Juke Boxes | 2 | November 26th 03 07:56 PM |