If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Tech: Seeburg Mech: after the cleaning
I took the plunge and cleaned my 220 mech. using the cleaner others
have posted on (Westley blech white). I was hesitant to use it, since the warning label said not to use it on aluminum or magnesium. It worked great. I spent about 30 min. blowing it dry with comp. air. I oiled / lubed it per the book, although I wish the diagrams would have been bigger. I "think" it is partially seized-up now. The motor is out, and it's very hard to turn the rubber motor shaft by hand. Should it be easy to turn? Any suggestions? Also, the book doesn't say which type of lube to use on the "turntable drive shaft gear (the big one on top that looks like it's made out of plastic). Should I use Lubriplate, or the mech oil? Is mine damaged, or will it start to ease up once all the gears and bearings have been oiled? Help! Ace |
Ads |
#2
|
|||
|
|||
Pop the upper motor shaft bearing assembly off and clean that with Gum-Out or
some other strong degreaser; you've probably got gunked-up oil in that bearing. Be careful not to lose the tiny steel thrust bearing that sits in the top of the bearing assembly. (The bearing assembly is the cylindrical part with a large hex nut that sits on the top of the carriage assembly just above the motor shaft; it's held in place by four screws.) Note that it's also possible that when you pulled the motor out the downward force exerted on the motor drive worm gear shaft may have wedged it against the fiber gear. Try a light upward tap or two on the bottom of the shaft to free it up. The fiber gear should be lubricated with Lubriplate. Tony In article .com, "Ace" wrote: I took the plunge and cleaned my 220 mech. using the cleaner others have posted on (Westley blech white). I was hesitant to use it, since the warning label said not to use it on aluminum or magnesium. It worked great. I spent about 30 min. blowing it dry with comp. air. I oiled / lubed it per the book, although I wish the diagrams would have been bigger. I "think" it is partially seized-up now. The motor is out, and it's very hard to turn the rubber motor shaft by hand. Should it be easy to turn? Any suggestions? Also, the book doesn't say which type of lube to use on the "turntable drive shaft gear (the big one on top that looks like it's made out of plastic). Should I use Lubriplate, or the mech oil? Is mine damaged, or will it start to ease up once all the gears and bearings have been oiled? Help! Ace |
#3
|
|||
|
|||
Hmmm i have cleaned several seeburgs with that soap and the garden hose
... I do always remove the whole worm gear clutch assembly off the back ( i didnt mention that before ) before i clean . This gives you the chance to totaly get that assembly cleaned and be able to turn the cam gear through its motions while oiling everything ....... and see how that motor rubber turns . It would turn a bit stiff if the mech is in mid stream otherwise it should turn fairly easy . Like someone said it may just be pulled down to far . Put the motor back in place & see how it turns it should turn with one finger . |
#4
|
|||
|
|||
After letting it sit overnight, it appears to have un-stuck itself. I
guess letting the oil set for a time helped? Anyway, it turns pretty freely now. (sigh of relief!). I do have a couple of questions: The carriage track - lubriplate or oil ? What about the camshaft - I coudn't find it on the lube chart on which type to use. Finally, does the motor reverse eletrically, or is there a reverse gear on the mech to make it scan in both directions? Thanks all for helping - Mark "Ace" |
#5
|
|||
|
|||
Good question on the lube.I would probably put a thin coat of lubriplate on the
carriage track.Don't know about the camshaft.The motor reverses electrically via the reversing switch on the front of the mech.Has a paddle that easily switches it left or right.Spring loaded so it stays one way or the other when gets switched.It gets activated at each end of the mechanism as it scans.If you ever remove the mech from the carriage frame you got to be careful because it can easily be damaged. After letting it sit overnight, it appears to have un-stuck itself. I guess letting the oil set for a time helped? Anyway, it turns pretty freely now. (sigh of relief!). I do have a couple of questions: The carriage track - lubriplate or oil ? What about the camshaft - I coudn't find it on the lube chart on which type to use. Finally, does the motor reverse eletrically, or is there a reverse gear on the mech to make it scan in both directions? Thanks all for helping - Mark "Ace" |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
TECH: preparing Seeburg Mechanism for cleaning | Ace | Juke Boxes | 4 | December 8th 04 04:36 AM |
TECH: preparing Seeburg Mechanism for cleaning | Ace | Juke Boxes | 0 | December 7th 04 09:32 PM |
TECH: Coin mech for S220 help | Homebru | Juke Boxes | 2 | October 31st 04 06:44 PM |
Cleaning Seeburg R mech end plastics | mikke | Juke Boxes | 1 | March 15th 04 01:11 PM |
Looking for Seeburg R Mech Cover | CraigBurnett | Juke Boxes | 0 | December 17th 03 04:51 AM |