If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below. |
|
|
Thread Tools | Display Modes |
#1
|
|||
|
|||
Rockola 1448 start relay ?
I need to replace a Rockola 1448 start realy (DC).I don't have any
other info to what size coil I need,I checked this relay with a ohm meter an didn't get a ready.Since there was a piece of plastic inserted in it to keep it energized,I'm assuming this is a bad coil.This is why the machine apparently keeps looking for a selection. (Earlier post) I'm getting close to the end of the mechanical restoration of this machine.Can someone tell me where to purchase these coils?I have no idea were to buy or what size coil this is. Hoping I can get this operating so I can start on restoring cabinet.Thanks |
Ads |
#2
|
|||
|
|||
Rockola 1448 start relay ?
Part # 18859 need only solinoid-relays intact
|
#3
|
|||
|
|||
Rockola 1448 start relay ?
do a search for jukebox parts and get phone #s . It worked well for me .
|
#4
|
|||
|
|||
Rockola 1448 start relay ?
On Nov 18, 7:48*pm, (Ken G.) wrote:
do a search for jukebox parts and get phone #s . It worked well for me . Wow-thanks Ken,I wasn't sure I would get a reply. I have a ton of pinball coils,so I think I'm going to try a "Hold" coil from a pinball.I've tried Williams,and they are a fraction too big.I have several Gottliebs I'll try next.If the size differance turns into a problem,I can either make adjustments to the contact holder or change it out completely for a pinball contact relay .My mind works slow sometimes. I couldn't imagine it would be that hard to find a small electronic piece that make the machine a go or blow--Without the start coil working the machine would either be dead,or constantly alive were you wish it was dead... Victory sells the other 2 coils in then machine,but not the one I need--- Thanks |
#5
|
|||
|
|||
Rockola 1448 start relay ?
On Nov 18, 10:49 pm, wrote:
On Nov 18, 7:48 pm, (Ken G.) wrote: do a search for jukebox parts and get phone #s . It worked well for me . Wow-thanks Ken,I wasn't sure I would get a reply. I have a ton of pinball coils,so I think I'm going to try a "Hold" coil from a pinball.I've tried Williams,and they are a fraction too big.I have several Gottliebs I'll try next.If the size differance turns into a problem,I can either make adjustments to the contact holder or change it out completely for a pinball contact relay .My mind works slow sometimes. I couldn't imagine it would be that hard to find a small electronic piece that make the machine a go or blow--Without the start coil working the machine would either be dead,or constantly alive were you wish it was dead... Victory sells the other 2 coils in then machine,but not the one I need--- Thanks I would not use a 30 volt pinball coil. I tried this once and it got hot quickly. Ended up putting a Bally 50 volt coil in it.This was a 448 R-O play control relay that was open. I think I used a G31-2000, but not real sure on this. This was an in-home service call & I never got a call-back so it may be a long-term fix. Also if your coil is not cooked, but just open the wires often break close to the terminals. You can often unwind one turn and solder it back on. Ray |
#6
|
|||
|
|||
Rockola 1448 start relay ?
It's cooked.I'll try a bally coil.
Thanks for the heads up. |
Thread Tools | |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rockola 1448 selection trouble | [email protected] | Juke Boxes | 1 | November 16th 08 06:17 AM |
Rockola 1448-1452 | Brian Roth | Juke Boxes | 0 | December 13th 07 02:33 AM |
Rockola 1448 dress cap | [email protected] | Juke Boxes | 0 | June 3rd 07 09:54 PM |
WTB: Rockola model 1454 and 1448 and Empress | Nimko Lodewijk | Juke Boxes | 1 | February 1st 07 02:03 AM |
Tech Rockola 448 mute relay | PhilR | Juke Boxes | 1 | August 12th 05 09:47 PM |